Innovation: Pool Table

Hi!

Check out my actually cool pocket billiards postpone project! It even has an semiautomatic ball return!

Materials:

- 36" x 48" paperboard (qty. 2) which is folded in two places to form a 24" x 36" center section and two 12" x 36" side sections.

- Cardboard 12" x 24" (accustomed track one end [cross-section] of the box)

- Cardboard 12" x 36" (used as a support for the pool table)

- Two 4" wide-screen x 36" semipermanent cardboard rectangles (in use for the lump return mechanism)

- Two 2" x 36" unlifelike rectangles and two 2" x 24" cardboard rectangles which will be used for the pool table rails

- A 3/4" x 12" piece of unreal that will be used to make the ball trigon.

- Green felt at any rate approximately 32" x 44"

- 2" wide cellophane packing tape

- corner tender

- 10 marbles

Step 1: Take shape the Dead body of the Table

Cut down a 24" x 36" rectangle of cardboard from one of the deuce poster boards. Taping this rectangle to the other poster board to form a box measuring 12" x 24" x 48".

Step 2: Close One End of the Pond Put of Body

Tape the 24" x 12" composition board rectangle to one remainder of the box

Step 3: Make the Pockets

For the pool postpone corner pockets, cut 2"-diameter tractor trailer-circles at each of the 4 corners of the table, and for the root pockets, cut a 2" semi-circle in the midst of apiece 36" margin.

Act up not discard the cut-up semi-circles. We bequeath use them advanced.

Step 4: Insert the Perpendicular Table Support

To tolerate the table, put across a 36"x12" cardboard in the middle of the interior of the box. Tape the hold up cardboard along the length of both of the top and nethermost cardboards.

Step 5: Form the Ball Return Troughs

To catch the balls, physique two V-shaped troughs: draw a line along the center of a 2"x36" cardboard and parallel to the 36"-long edges. Sheepcote the rectangle along the line to soma a V-shape through. Do the same to the other 2"x36" cardboard.

Step 6: Place the First Set of Ends on the Troughs

Tape one of the cut-up semi-circles to one end of each V-shaped trough. Make doomed that the straight edge of the semi-circle is at the top of the inning of the "V".

Step 7: Add the Second Set of Ends on the Troughs

Tape one of the cut-up semi-circles to the odd end of each Formed trough. This time, make predictable that the snaky margin of the semi-lot is at the top of the "V".

Pace 8: Match the Shape of the Semi-circle to the Inner Wall of the Box

The troughs testament mount beneath the pockets and ready to make the troughs consist against the walls, it is necessary to trim the rig-circles. Only trim the semi-circles that have the unmodulated march across the top of the "V". For the gutter that mounts on the redress hand side of the box (shown in impression), cut the semi-circle happening its honorable root thus that IT can placed flat upward against the 36" fence. For the other trough which mounts on the left field side of the box, crop the semitrailer-circle on its left position so that it can lie even against the left hand fence. For some the left and right troughs, the original flat part of the semi-circles at the top of the "V" are settled unqualified against the exceed of the box as shown.

Step 9:

Step 10: Install the Troughs

Using tape, fasten the troughs inside at an angle along the 36"-long side of the put of. Notice that you will have to trim the semi-circles near the open end of the box (fair-and-square the likes of you did in the close step) systematic for the rig-circles to lie flat against the walls of the package.

Step 11: Set u the Felt

Mangle whatever felt for the table, pull it tense, and utilization tacks to fix IT to the sides of the box.

Step 12: Trace the Locations of the Pockets

Use a marker to trace on the felt the cut-up holes and cut the holes in the felt.

Step 13: Mag tape the Rails to the Postpone

I made mine 2" tall, but you can adjust to fit your taste.

Step 14: Make the Triangle

Place the marbles in the shape of a triangle, manikin the 3/4" x 12" cardboard around the triangle, and tape the ends. Cutoff an excess length.

Step 15: Play Syndicate!!!!

I use of goods and services a 1/4" wooden dowel about 2 - 3' long as my pond cue.

Voila! Information technology's a blast!

Be the First to Apportion

Recommendations

  • Anything Goes Contest 2022

    Anything Goes Contest 2022